• No straight-pipe requirement!  Place immediately after a bend or valve, even in the same valve box  (Jumbo size valve box recommended for easiest fit)
• Read very low and high flow, all in one sensor
• No moving parts for greater reliability and allowing blowout for winterization with the sensor installed
• Pressure rated to 200 PSI and an operating temperature of 32 - 150 degrees Fahrenheit
• On-board LED Lights indicating power, full pipe status, relative forward flow rate, and reverse flow
• Simple setup at the controller with a standard K and Offset value for wide compatibility
• Uses internal ultrasonic transducers and acoustical reflectors to sense flow
• Designed for outdoor or underground applications (upper electronics are IP 68 / NEMA 4X rated)
• Glass Filled Nylon body construction for high pressure rating (200 PSI)

Flow Sensors Enable Key Controller Features

Flo-Watch™. Flo-Watch constantly monitors for low flow and excess flow conditions caused by broken lines or heads, automatically quarantines and shuts down the problem area, and continues to irrigate non-affected areas. Saves water, saves plant material, and enables irrigation programs to continue and complete

Learned Flow. The controller automatically learns station flow rates resulting in more accurate flow rates. The automatic collection prevents you from having to manually enter data from drawings, or physically visiting each valve to collect flow data and manually entering the data into a controller

FloManager®. FloManager determines the optimal station irrigating sequence. The system runs at its fullest capacity until programs are complete. The controller automatically selects and runs multiple valves at the same time within hydraulic parameters, allowing for shorter water windows

Sensor Features Specs

Flow Range

• No straight-pipe requirement!  Place immediately after a bend or valve, even in the same valve box  (Jumbo size valve box recommended for easiest fit)
• Read very low and high flow, all in one sensor
• No moving parts for greater reliability and allowing blowout for winterization with the sensor installed
• Pressure rated to 200 PSI and an operating temperature of 32 - 150 degrees Fahrenheit
• On-board LED Lights indicating power, full pipe status, relative forward flow rate, and reverse flow
• Simple setup at the controller with a standard K and Offset value for wide compatibility
• Uses internal ultrasonic transducers and acoustical reflectors to sense flow
• Designed for outdoor or underground applications (upper electronics are IP 68 / NEMA 4X rated)
• Glass Filled Nylon body construction for high pressure rating (200 PSI)

• No straight-pipe requirement!  Place immediately after a bend or valve, even in the same valve box  (Jumbo size valve box recommended for easiest fit)
• Read very low and high flow, all in one sensor
• No moving parts for greater reliability and allowing blowout for winterization with the sensor installed
• Pressure rated to 200 PSI and an operating temperature of 32 - 150 degrees Fahrenheit
• On-board LED Lights indicating power, full pipe status, relative forward flow rate, and reverse flow
• Simple setup at the controller with a standard K and Offset value for wide compatibility
• Uses internal ultrasonic transducers and acoustical reflectors to sense flow
• Designed for outdoor or underground applications (upper electronics are IP 68 / NEMA 4X rated)
• Glass Filled Nylon body construction for high pressure rating (200 PSI)

USSAM UNISPRAY SAM RETRO

Residential Installation (Indoor use only). Replacement for transformers with output of 650mA or less. The transformer is compatible with these Rain Bird timer models:

• SST Indoor: SST-400i, SST-600i, SST-900i

Rain Bird timer models other than SST Indoor may require additional tools and expertise in order to use this replacement transformer. If there is any doubt about the use of this product please consult a professional electrician.

• Locking Hex bolt with washer and clip for all Rain Bird valve boxes

• Includes red wire nut and direct bury silicon-filled tube
• Ideal for use on two wire decoder control systems.
• Use for standard controllers, valve boxes and soil moisture sensors.
• Wire combinations ranging from 22ga to 8ga.
• Use on connections from 24 VAC to 600 VAC.
• UL 486D listed as a sealed wire connector system.
• The Strain Relief ensures wires are secure and won't pull apart.
• Waterproof silicone grease protects against corrosion.
• UV- material ensures product performance does not degrade even after long periods of exposure to sunlight.

• Ideal for irrigation systems, landscape lighting, and other exterior wiring.
• Stops Corrosion In Its Tracks.
• Eliminates need for heat shrink, tape, or sealants.
• No Pre-Twisting of Wire Necessary.
• Winged caps are easy to tighten and remove.
• Superior Surge Resistance.
• Silicon gel-filled connectors are rated for 600 volt maximum use with 22 to 12 gauge wire.
• Simply insert wires into the cap and twist.

   

   

  Waterproof Wire Connectors Guide

Battery replacement for WR2-RFC and WR2-48 Rain/Freeze Sensor.  Includes Lithium Ion CR2032 replacement battery and battery cap.

• Replacement 200 mesh (75 micron) filter screen and three O-rings for Rain Bird Xeri-Bird 8 multi-outlet drip emission device